Skip to main content
Research and Innovation

Researchers Use Liquid Shearing Method to Create Nanofiber ‘Gusher’

NC State researchers use shearing method to create polymer nanofibers in liquid. Photo courtesy of Orlin Velev.

For Immediate Release

Creating large amounts of polymer nanofibers dispersed in liquid is a challenge that has vexed researchers for years. But engineers and researchers at North Carolina State University and one of its start-up companies have now reported a method that can produce unprecedented amounts of polymer nanofibers, which have potential applications in filtration, batteries and cell scaffolding.

In a paper published online in Advanced Materials, the NC State researchers and colleagues from industry, including NC State start-up company Xanofi, describe the method that allows them to fabricate polymer nanofibers on a massive scale.

The method – fine-tuned after nearly a decade of increasing success in producing micro- and nanoparticles of different shapes – works as simply as dropping liquid solution of a polymer in a beaker containing a spinning cylinder. Glycerin – a common and safe liquid that has many uses – is used to shear the polymer solution inside the beaker along with an antisolvent like water. When you take out the rotating cylinder, says Dr. Orlin Velev, Invista Professor of Chemical and Biomolecular Engineering at NC State and the corresponding author of the paper describing the research, you find a mat of nanofibers wrapped around it.

When they first started investigating the liquid shearing process, the researchers created polymer microrods, which could have various useful applications in foams and consumer products. “However, while investigating the shear process we came up with something strange. We discovered that these rods were really just pieces of ‘broken’ fibers,” Velev said. “We didn’t quite have the conditions set perfectly at that time. If you get the conditions right, the fibers don’t break.”

NC State patented the liquid shear process in 2006 and in a series of subsequent patents while Velev and his colleagues continued to work to perfect the process and its outcome. First, they created microfibers and nanoribbons as they investigated the process. “Microfibers, nanorods and nanoribbons are interesting and potentially useful, but you really want nanofibers,” Velev said. “We achieved this during the scaling up and commercialization of the technology.”

Velev engaged with NC State’s Office of Technology Transfer and the university’s TEC (The Entrepreneurship Collaborative) program to commercialize the discoveries. They worked with the experienced entrepreneur Miles Wright to start a company called Xanofi to advance the quest for nanofibers and the most efficient way to make mass quantities of them.

“We can now create kilograms of nanofibers per hour using this simple continuous flow process, which when scaled up becomes a ‘nanofiber gusher,’” Velev said. “Depending on the concentrations of liquids, polymers and antisolvents, you can create multiple types of nanomaterials of different shapes and sizes.”

“Large quantities are paramount in nanomanufacturing, so anything scalable is important,” said Wright, the CEO of Xanofi and a co-author on the paper. “When we produce the nanofibers via continuous flow, we get exactly the same nanofibers you would get if you were producing small quantities of them. The fabrication of these materials in liquid is advantageous because you can create truly three-dimensional nanofiber substrates with very, very high overall surface area. This leads to many enhanced products ranging from filters to cell scaffolds, printable bioinks, battery separators, plus many more.”

The research was funded by the National Science Foundation’s Accelerating Innovation Research program. NC State’s researchers Stoyan Smoukov, Tian Tian and Eunkyoung Shim co-authored the paper, as did Narendiran Vitchuli, Sumit Gangwal, Miles Wright and Pete Geisen from Xanofi Inc.; Manuel Marquez from Ynano Llc.; and Jeffrey Fowler from Syngenta Co.

– kulikowski –

Note to editors: An abstract of the paper follows.

“Scalable Liquid Shear-Driven Fabrication of Polymer Nanofibers”

Authors: Stoyan Smoukov, Tian Tian, Eunkyoung Shim and Orlin Velev, North Carolina State University; Narendiran Vitchuli, Sumit Gangwal, Miles Wright and Pete Geisen, Xanofi Inc.; Manuel Marquez, Ynano Llc.; and Jeffrey Fowler, Syngenta Co.

Published: March 18, 2015, online in Advanced Materials

DOI: 10.1002/adma.201404616

Abstract:  A simple process for batch or continuous formation of polymer nanofibers and other nanomaterials in the bulk of a sheared fluid medium is introduced. The process could be of high value to commercial nanotechnology as it can be easily scaled up to the fabrication of staple nanofibers at rates that could exceed tens of kilograms per hour.