Skip to main content
Research and Innovation

Lightweight, Wearable Tech Efficiently Converts Body Heat to Electricity

TEG-embedded T-shirt (left) and TEG armband (right).

For Immediate Release

Researchers at North Carolina State University have developed a new design for harvesting body heat and converting it into electricity for use in wearable electronics. The experimental prototypes are lightweight, conform to the shape of the body, and can generate far more electricity than previous lightweight heat harvesting technologies.

Study co-lead Haywood Hunter, shows off the TEG-embedded T-shirt at work.
Study co-lead Haywood Hunter, shows off the TEG-embedded T-shirt at work.

The researchers also identified the optimal site on the body for heat harvesting.

“Wearable thermoelectric generators (TEGs) generate electricity by making use of the temperature differential between your body and the ambient air,” says Daryoosh Vashaee, an associate professor of electrical and computer engineering at NC State and corresponding author of a paper on the work. “Previous approaches either made use of heat sinks – which are heavy, stiff and bulky – or were able to generate only one microwatt or less of power per centimeter squared (µW/cm2). Our technology generates up to 20 µW/cm2 and doesn’t use a heat sink, making it lighter and much more comfortable.”

The new design begins with a layer of thermally conductive material that rests on the skin and spreads out the heat. The conductive material is topped with a polymer layer that prevents the heat from dissipating through to the outside air. This forces the body heat to pass through a centrally-located TEG that is one cm2. Heat that is not converted into electricity passes through the TEG into an outer layer of thermally conductive material, which rapidly dissipates the heat. The entire system is thin – only 2 millimeters – and flexible.

“In this prototype, the TEG is only one centimeter squared, but we can easily make it larger, depending on a device’s power needs,” says Vashaee, who worked on the project as part of the National Science Foundation’s Nanosystems Engineering Research Center for Advanced Self-Powered Systems of Integrated Sensors and Technologies (ASSIST) at NC State.

The researchers also found that the upper arm was the optimal location for heat harvesting. While the skin temperature is higher around the wrist, the irregular contour of the wrist limited the surface area of contact between the TEG band and the skin. Meanwhile, wearing the band on the chest limited air flow – limiting heat dissipation – since the chest is normally covered by a shirt.

In addition, the researchers incorporated the TEG into T-shirts. The researchers found that the T-shirt TEGs were still capable of generating 6 µW/cm2 – or as much as 16 µW/cm2 if a person is running.

“T-shirt TEGs are certainly viable for powering wearable technologies, but they’re just not as efficient as the upper arm bands,” Vashaee says.

“The goal of ASSIST is to make wearable technologies that can be used for long-term health monitoring, such as devices that track heart health or monitor physical and environmental variables to predict and prevent asthma attacks,” he says.

“To do that, we want to make devices that don’t rely on batteries. And we think this design and prototype moves us much closer to making that a reality.”

The paper, “Wearable thermoelectric generators for human body heat harvesting,” is published in the journal Applied Energy. Lead authors of the paper are Melissa Hyland, a graduate student at NC State, and Haywood Hunter, an undergraduate at NC State. They worked on the project while undergraduates, with support from an NSF Research Experiences for Undergraduates grant. Co-authors include Jie Liu, a postdoctoral researcher at NC State; and Elena Veety, education director of ASSIST at NC State. The work was funded by the NSF under grants EEC-1160483, ECCS-1351533 and CMMI-1363485; and by the Air Force Office of Scientific Research under grant FA9550-12-1-0225.


Note to Editors: The study abstract follows.

“Wearable thermoelectric generators for human body heat harvesting”

Authors: Melissa Hyland, Haywood Hunter, Jie Liu, Elena Veety, and Daryoosh Vashaee, North Carolina State University

Published: online Aug. 27, Applied Energy

DOI: 10.1016/j.apenergy.2016.08.150

Abstract: A thermoelectric generator (TEG) can be used to harvest electrical energy from human body heat for the purpose of powering wearable electronics. At the NSF Advanced Self-Powered Systems of Integrated Sensors and Technologies (ASSIST), TEGs are one of the enabling technologies being explored to advance the center’s mission of creating wearable, self-powered, health and environmental monitoring systems. As part of this effort, an exploration of the relevant parameters for maximizing the wearable TEG power output from the body heat and maintaining the body comfort is particularly important. For this purpose, the heat from the body must be directed into TEG with minimal loss, the generator must be designed for maintaining a high temperature differential across the thermoelectric material, and the generator must have a small form factor to maintain the body comfort. In order to address these requirements, an optimum TEG design was developed and experiments were conducted both on a temperature-controlled hot plate and on different body locations including the wrist, upper arm, and chest. The TEG was further fabricated into a T-shirt and the power was recorded for different human activities. Comparison of the experiments on various body locations and on the T-shirt yielded the highest to lowest power generated on the upper arm, wrist, chest and T-shirt, respectively. The prospect of powering a wearable electrocardiogram sensor by a TEG on the upper arm is discussed.

Leave a Response

Your email address will not be published. All fields are required.

  1. How much do these cost? I’m working on a project and such information would be appreciated. Thank you!

  2. Is this device in production and can it be used to charge cell phones. What does it cost.Can licenses be issued for local production

  3. Hello
    My name is abhay and I would like to know more details about wearable TEG, where can i buy and cost of these TEG

  4. Good day,

    I’m Zylyn Tisbe, an incoming senior student of De La Salle – College of Saint Benilde in the Philippines, currently studying Interior Design. This article really helped for the start up of my thesis project and I myself, would like to know more details about TEG. I hope I could have a contact with you guys so I could ask questions for my project. I planned for designing a seating furniture with TEG.

    I hope you could help me with this.

    This is indeed a fine innovative work.

    Best regards,
    Tisbe, Zylyn

  5. Hi my name is Thomas and I’m currently working on my senior project and I was wondering if I could find out the cost of one of these TEG’s so I could use one in my project.

  6. This is amazing technology, do you have any idea of what the cost of one of your TEGs would be? I’m pretty interested in getting one and trying it out.

    I hope It would be economically viable, it would be a great way to start a future in wearable TEGs. Thanks!

  7. I generate enough heat from my exercise to light up a building!

    This stuff has to be really good for the future. Go ASSIST!

  8. permission to use image. I am writing a book on augmented reality (for Springer) and would like to use the photo above. May I?

  9. I love this. I own a North Carolina apparel company that would be interested in knowing more. Mindful supply. We are truly vested in local and love Ncsu. We work with cotton Inc and the textile Dept currently

    1. Hi David,
      Thank you for expressing your interest in this innovative tech, and your enthusiasm for NC State. My name is Jason Lamb, and I manage this ASSIST developed technology through the Office of Technology Commercialization and New Ventures. If you’d like to learn more do not hesitate to reach out to me at 919-515-7199. I look forward to speaking to you.